get_lldp_neighbors() existed but spoke to the older CLI generation: it ran
`show lldp remote-device all` and expected FASTPATH-style `0/1` ports in
whitespace-separated columns. v7 firmware answers `Unknown command` — as it
does for `show lldp remote-device`, a bare `show lldp`, and the plural
`show lldp neighbors`. Only the singular works, though `show ?` lists `lldp`
plainly enough:
Port | Device ID | Port ID | SysName | ...
---- + ----------------- + ---------------- + ----------------- + ...
g9 | 10:01:02:44:37:26 |10:01:02:44:37:28 | pve-eze.eze.local | ...
Ports are named g9, and the columns are separated by `|` with irregular
padding, so splitting on whitespace tears the values apart. The port ID is
not always a port name either — a neighbour may identify its port by MAC.
_get_lldp_table() now branches on _detect_cli_v7() into a second parser, the
same shape get_mac_address_table() already uses for this divergence.
get_lldp_neighbors() itself is untouched.
Confirmed against a GS110TPv3 on 7.1.1.17: _detect_cli_v7() returns True
there, and the switch reports two neighbours it had never surfaced. Without
them NetOrk's map had nothing to draw for the site this switch serves, so
four APs and a firewall behind it stood unconnected.
`show running-config` is preceded by a header block, and one of its lines
reports the system uptime. That value necessarily differs between any two
reads, so every caller comparing consecutive configs sees a change each
time.
Measured on a GS110TPv3 under NetOrk: 876 of 894 stored config snapshots
marked as changed, one git commit and one config_changed warning per poll,
while every other device at the same installation sat between 2 and 18. The
history was worthless for that switch — a genuine change would have been
invisible among hundreds of uptime diffs.
Only the uptime line is removed. Model, firmware version, serial and MAC are
stable and belong in a config backup; a changed firmware version is exactly
the kind of change worth recording.
netgear_plus is unaffected — its get_config() returns empty strings.
The first read after this lands reports one real change, since the line
disappears from the stored config. That is unavoidable and happens once.
"v7" CLI firmware has no "terminal length 0" equivalent (see
_send_paged_command's docstring), so a config long enough to paginate
emits "--More--" prompts that _send_command's expect_string=base_prompt
match never sees. On real hardware (GS110TPv3, 7 VLANs, 10 interfaces)
this hung every scheduled config-backup poll for 30s and failed with
"Pattern not detected: '<prompt>[>#]' in output.", so the config was
never actually backed up. get_mac_address_table()/get_vlans() already
use _send_paged_command() for the same reason on other long outputs;
get_config() now does too.
Also fixed tests/unit/test_driver.py's import/patch target
(napalm_netgear_plus -> napalm_netgear, the actual package name) —
the whole file has been uncollectable since its initial commit, no CI
was wired up here to catch it. And removed a dead unreachable
`return {"success": ..., "output": ...}` line after get_health_metrics's
real return (undefined names, ruff F821), unrelated leftover found
while fixing the above.
_conf_prompt() only matched the legacy "(Config)" prompt, so on v7
"Cisco-like" CLI (lowercase "(config)") _enter_config_mode() blocked for
the full read_timeout - this was the cause of fix_snmp hanging.
_action_fix_snmp() also never returned a result on the legacy path, and
v7 firmware has no snmp-server/show snmp commands at all. It now detects
v7 CLI up front and returns a clear failure message instead of hanging.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
get_poe_status()/set_poe() implement PoE port config via the ProSafe CLI's
'power inline' interface sub-commands. get_interfaces() now enriches chN
LAG entries and their member ports with trunk_group/lag_members/lag_mode
by parsing 'show port-channel all'. New set_lag_members() adds/removes
members via addport/deleteport.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
SNMP health metrics using Netgear enterprise MIB (OID 4526) for
memory free/total and CPU utilization string parsing, plus IF-MIB counters.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
NetgearPlus: get_snmp_config() returns None (SNMP not accessible via HTTP API).
NetgearSmart: get_snmp_config() reads current community, fix_snmp configures
'snmp-server community public ro' via CLI.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Christian Manivong